MENU

Menu

Konference

2025

2025

27. 5. – 29. 5. 2025, Hradiště nad Jizerou

TU v Liberci

Comparison of Fatigue Crack Initiation in Bonded Patches

A. Karkulín, M. Kadlec, B. Cabrnoch

Effect of Waste Glass Surface Modification on the Mechanical Properties of Cement Composites

Z. Prošek, A. Palička, O. Babčenko

Effective Mechanical Characteristics of 3D Printed Structures with Gradient Elastic Characterics

V. Afanaseva, A. Jíra

Evaluating Poisson’s Ratio in Conventional and Auxetic Cellular Structures

J. Kostka, B. Schürger, P. Frankovský, P. Palička, M. Hagara

Experimental and Numerical Investigation of Auxetic Structures Using Photoelasticity and FEM

B. Schürger, P. Frankovský, M. Pástor, P. Lengvarský, J. Kostka, P. Palička

Experimental Investigation of PA6 GF under Tensile and Relaxation Loading

J. Prajka, R. Halama, M. Šofer, T. Vlček

Experimental Study of Inclined Angle Influence on Static and LCF properties of Additively Manufactured Aluminium Alloy

R. Halama, M. Kořínek, J. Čapek, K. Trojan, N. Ganev, J. Hajnyš

Identification of Paddle Motion During Kayak Paddling

B. Kropík, Z. Padovec, M. Fošnarič, T. Mareš

Infuence of Etching on the Mechanical Properties of Thin 3D Printed Ti6Al4V Alloy Specimens

P. Bočan, A. Jíra

Mechanical and Thermal Properties Influenced Heat Treatment of Basalt Fibers-Vermiculite-Doped Geopolymer

M. Ryvolová, M. Mrózek, O. Vích, T. Bakalova

On a Possibility of High-Resolution Neutron Diffraction Studies of High-Entropy Ceramics Substructure

P. Mikula, V. Ryukhtin, J. Dusza

Comparison of Incremental and DIC-Based Determination of the Cyclic Stress-Strain Curve for SLM AlSi10Mg

J. Cienciala, M. Fusek, R. Halama, M. Mánek, J. Šimota, Z. Pitrmuc

Performance Optimization of CFRP Retaining Sleeve for Rotors via Controlled Filament Winding Pre-Stress: Experimental Approach

O. Pavlík, T. Návrat, G. Cabaj, M. Vajdák

Predicting the Fatigue Lifetime of Laser Powder Bed Fusion-processed Alloys Using Physics-informed Neural Networks

J. Halamka, O. Stránský, L. Beránek, M. Bartošák

Residual Stress Measurement in the Cold Spray Layers

R. Musilová, M. Vostřák, A. Krasij, J. Václavík, M. Švantner

Tensile Properties of 3D Printed Infill Structures with Different Densities

J. Heczko, J. Krystek, V. Laš

Tension-compression Tests of 3D-printed PETG

T. Vaňková, J. Krystek

The Effect of Printing Direction on the Properties of Thermoplastic Elastomers

M. Hančinová, E. Dubňanská, R. Huňady, P. Palička

Using a friction sensor in experimental stress analysis

J. Václavík, R. Musilová, V. Yanovych

Validation of Polymer Material Model Using Tensile Test Simulations and Mesh Sensitivity Analysis

P. Palička, M. Hagara, B. Schürger , R. Huňady

X-ray Diffraction Analysis of Preferred Orientation and Residual Stresses of Aluminium Alloy Manufactured by Selective Laser Melting Technology

J. Čapek, K. Trojan, R. Halama, N. Ganev, J. Hajnyš

Compression Behavior of 3D-Printed stochastic Structures at Varying Densities

A. Boualleg, D. Cirkl

Computer Simulation of the Isothermal Forming Process of a Glass Element

M. Horák, M. Stará, G. Kehlerová

Design of a Sensor Network for In-flight Thrust Measurements of a Jet Training Aircraft Propulsion Unit

R. Doubrava, J. Raška

Design of Magnetoactive Soft Gripper Using a Genetic Algorithm

M. Hermann, I. Petríková

Detection of Surface Degradation and Damage Criteria Based on Image Processing

J.Pavlas, J. Krčil, S. Slavík, M. Růžička

Determination of Rotary Joint Stiffness Coefficients using Modal Analysis

R. Huňady, T. Poštulka, M. Hagara, P. Palička, Z. Bobovský

Development and Experimental Validation of Sensors for Structural Health Monitoring of Composite Structures

M. Růžička, N. Schmidová, K. Doubrava, D. Blaha, D. I. Exner, T. Ridoško

Proceedings of the 63th Annual Conference on Experimental Stress Analysis

Copyright | Všechna práva vyhrazena | www.experimentalni-mechanika.cz | Tvorba: GLIPS